A roof in Annapolis and a roof in Oakland sit in the same state and answer to different weather. The Annapolis roof faces salt air, wind-driven rain off the Chesapeake, and the tail end of every tropical system that runs up the coast. The Oakland roof sits at nearly 2,400 feet in Garrett County, where the 1991–2020 normals put annual snowfall near 107 inches and the State Archives puts the county ceiling at 110. Between them, Baltimore holds a third roofing market altogether: rows of brick rowhomes with flat roofs behind parapet walls, priced by the membrane rather than the shingle, in a housing stock whose median structure year is 1946. One statewide price cannot describe all three. This guide does not try. It prices the state from the anchors up, then separates the Bay, the rowhome, and the mountain roof so each quote can be read against the right market.
The order below follows the order a Maryland homeowner actually decides in. The statewide anchors come first, with every published model shown side by side and the high outlier flagged rather than hidden. Then each material is priced on the same 25-square roof, with the before-tear-off rows labeled so they cannot be mistaken for fitted prices. Roof size comes next, because the commonest budgeting error in this state is pricing the living area instead of the roof surface. Then the cities, then the three forces that set Maryland prices — Bay wind and salt, the rowhome flat roof, and the western winter — then the license, the permit patchwork, the hurricane deductible, and the money. Every figure carries a source and a date. Every conflict between sources is printed rather than smoothed over. And nothing unverified is stated as fact anywhere in the guide.
The national picture behind every figure below sits in our roof replacement cost guide, and Maryland is measured against that baseline throughout. Where the roof meets the rest of the house, two Maryland guides complete the picture: our heat pump cost in Maryland guide prices the system that often goes in alongside a reroof, and our solar panel cost in Maryland guide prices the array that should never go on a roof with fewer than eight to ten years of life left in it.
Table of Contents
What a Roof Replacement Costs in Maryland in 2026
Two anchors frame the Maryland market, and they measure the job in different units, which is why homeowners comparing them often think they disagree when they do not. SmartRoofingCalculator counts in squares and prices architectural shingles at $470–$670 per square fitted with tear-off, which makes a typical 25-square roof $11,750–$16,750. NumeralQ counts in square feet of roof surface and prices a 2,000 square foot roof at $10,110–$12,360 statewide, pricing October 26, 2026. Convert the units and the two anchors overlap. A 2,000 square foot roof surface is 20 squares, and the per-square band across 20 squares gives $9,400–$13,400 — SmartRoofingCalculator’s own figure for a 2,000 square foot single-family home — which brackets NumeralQ’s band almost exactly. The difference between the two is measurement, not market.
The other published models fan out around that center, and the fan is wider in Maryland than in most states because the state’s labor market is. MyRoofData’s 2026 model runs higher, at $14,250–$24,500 for a typical single-family architectural roof, about 10 percent above the national average, built from crew rates of $60–$100 an hour and a state cost index of 1.10. Modernize, updated August 27, 2026, runs lower, at an average of about $14,000 for an architectural asphalt roof on a typical 1,800 to 2,200 square foot home, with most projects between $9,000 and $22,000, split roughly $8,500 in materials and $5,500 in labor. RoofingEstimatorPros runs highest of all, updated August 26, 2026: $15,881–$28,361 for a 2,000 square foot architectural roof, averaging $21,428, or about $10.71 per square foot with tear-off, permits, and waste included. Angi’s Baltimore figures, updated May 28, 2026, put a shingle roof in the city at an average near $10,973, ranging from $7,838 to $25,080, with labor near $6,580, almost 60 percent of the total. HomeYou, updated September 3, 2026, puts Baltimore at $10,448–$21,151, averaging $13,841. HomeCostLens, with cost data reviewed in September 2026, puts Baltimore near $11,500, ranging from $9,410 to $18,810. HomeQuoteHQ puts Baltimore at $11,200 on average, ranging from $8,200 to $16,500. SquareDash, quoting fixed prices from satellite measurements in April 2026, puts Baltimore at $15,200 for a 2,000 square foot home.
Two contractor-sourced ranges sit below the planning models and deserve their own reading. JDH Remodeling, working from more than 1,460 inspections across Southern Maryland between 2024 and 2026, prices most Maryland homes at $9,500–$20,000, with a two-story colonial at $9,500–$15,000 and a townhome or rancher at $5,500–$8,500, and cites a real 2026 job — a two-story colonial in Prince Frederick with about 2,000 square feet of roof surface, fitted with a full Owens Corning Platinum system, at $14,900. Monarch Bay Renovations prices the Baltimore metro at $8,000–$16,000 for a standard asphalt shingle home, about $4–$7 per square foot installed. A Southern Maryland contractor and a Baltimore contractor are pricing the houses they actually stand on, which skew smaller and simpler than the statewide planning models assume. Neither range is wrong. Each describes a different slice of the housing stock.
Maryland sits above the national average on every model that publishes a comparison, and the wage line explains why. SmartRoofingCalculator applies a state factor of 1.035 and ranks Maryland 39th of 50 from cheapest to most expensive. MyRoofData applies a 1.10 cost index. RoofingEstimatorPros applies a 1.12 state multiplier with a 1.15 labor multiplier. NumeralQ puts the state 4 percent above the national figure for the typical job. The Bureau of Labor Statistics, in its May 2025 Occupational Employment and Wage Statistics, puts the median Maryland roofer at $28.89 an hour, with a mean of $29.63 and about 2,050 roofers working statewide, against a national median of $26.65 — the state ranks 12th of 51 for roofer pay. One conflict belongs in the open: SmartRoofingCalculator, on a May 2024 BLS vintage, lists the Maryland roofer median at $25.00 an hour and the mean at $28.55, with about 2,520 roofers. This guide uses the May 2025 number. Against the neighbours, Maryland is the dearest roof in its own borderland on the SmartRoofingCalculator page: Pennsylvania at $440–$640 a square, Delaware and Virginia both at $430–$620, West Virginia at $390–$560. A contractor based over the line prices from a cheaper labor market, which is worth one quote on a job near the border — provided the contractor holds the Maryland license the job requires, which the hiring section takes up below.
RoofingEstimatorPros deserves a caution flag as the high outlier: its $21,428 average runs roughly half again above the SmartRoofingCalculator midpoint, and reads as the price of a large, steep, or complex job rather than a standard Maryland colonial. SquareDash deserves the same flag from a different direction: its $15,200 Baltimore figure is a fixed satellite price for a premium Owens Corning installation, not a planning band. Carry two numbers into the first contractor meeting: $11,750–$16,750 for a 25-square roof, and $10,110–$12,360 for a 2,000-square-foot roof as the independent check on it. In fair weather, a crew finishes a standard-pitch asphalt roof within one to three days, while a metal installation runs longer. The calendar around the install is what eats the time — collecting three quotes, waiting out the May-to-July hail peak if the old roof can hold, and confirming with the building department whether the job needs a permit at all, which in Maryland depends on the county and sometimes the street.
| Source | Typical job | Price | Dated |
|---|---|---|---|
| SmartRoofingCalculator | 25-square architectural roof | $11,750–$16,750 ($470–$670/sq) | Apr 24, 2026 / index Nov 9, 2026 |
| NumeralQ | 2,000 sq ft roof, statewide | $10,110–$12,360 | Oct 26, 2026 |
| NumeralQ | 2,000 sq ft roof, Baltimore | $9,790–$11,950 | Oct 26, 2026 |
| NumeralQ | 2,000 sq ft roof, Rockville | $9,960–$12,160 | Oct 26, 2026 |
| MyRoofData | Typical single-family arch roof | $14,250–$24,500 | 2026 model |
| Modernize | Average replacement | ~$14,000 (range $9,000–$22,000) | Aug 27, 2026 |
| RoofingEstimatorPros | 2,000 sq ft arch roof | $15,881–$28,361 (avg $21,428) | Aug 26, 2026 |
| Angi | Shingle roof, Baltimore | ~$10,973 avg (range $7,838–$25,080) | May 28, 2026 |
| HomeYou | Replacement, Baltimore | $10,448–$21,151 (avg $13,841) | Sep 3, 2026 |
| HomeCostLens | Replacement, Baltimore | $9,410–$18,810 (avg ~$11,500) | Sep 2026 |
| HomeQuoteHQ | Replacement, Baltimore | $8,200–$16,500 (avg $11,200) | 2026 |
| SquareDash | 2,000 sq ft home, Baltimore | $15,200 fixed price | Apr 2026 |
| JDH Remodeling | Most MD homes (Southern MD jobs) | $9,500–$20,000 | 2024–2026 jobs |
| Monarch Bay | Baltimore metro asphalt | $8,000–$16,000 | 2026 guide |
Roof Replacement Cost in Maryland by Material
Maryland’s material table carries a warning that belongs above the numbers rather than below them: three of its rows are priced before tear-off and the rest are priced with it, and mixing the two up understates a job by $2,500 to $5,000 on a 25-square roof. MyRoofData prices its per-square bands before tear-off and charges tear-off separately at $100–$200 per square per layer. SmartRoofingCalculator prices its bands fitted, tear-off included. The table below keeps both kinds of row, labels each, and prices a typical 25-square roof — 2,500 square feet of surface — material by material. Read it with the Bay in mind, not just the sticker: the cheapest shingle on the shelf is the one most likely to lift in a nor’easter, and the dearest metal on the shelf is the one most likely to still be shedding salt wind when the mortgage is paid off.
| Material | Installed cost per square | Total for 25 squares | Realistic life in Maryland |
|---|---|---|---|
| 3-tab asphalt shingle | $385–$605 (before tear-off) | $9,625–$15,125 | 15–20 yrs |
| Architectural asphalt shingle | $470–$670 | $11,750–$16,750 | 20–25 yrs |
| Class 4 impact-resistant shingle | $500–$700 (modeled) | $12,500–$17,500 | 25–30 yrs |
| Ribbed metal (exposed fastener) | $605–$1,045 (before tear-off) | $15,125–$26,125 | 30–40 yrs |
| Standing-seam metal | $930–$1,450 | $23,250–$36,250 | 40–60 yrs |
| Cedar shakes and shingles | $990–$1,650 (before tear-off) | $24,750–$41,250 | 20–30 yrs |
| Tile (concrete/clay) | $1,240–$1,860 | $31,000–$46,500 | 50+ yrs |
| Natural slate | $1,650–$3,300 (before tear-off) | $41,250–$82,500 | 75–150 yrs |
| Flat membrane (TPO/EPDM) | $605–$1,045 (before tear-off) | $15,125–$26,125 | 20–30 yrs |
The 3-tab row is a budget line, not a recommendation for most Maryland homes. MyRoofData prices 3-tab at $385–$605 a square installed before tear-off, and NumeralQ prices a 2,000 square foot 3-tab job at $8,360–$9,930, about 19 percent under architectural. It is a single flat layer with the weakest wind rating in this guide and no impact rating a Maryland insurer would credit. Insurers and builders have largely moved past it, and on a Bay-facing slope its low wind rating is the wrong place to save money. Each summer, humid heat and ultraviolet wear the granular surface a little thinner, and each winter the freeze-thaw cycle works the sealant strips a little looser, so the saving on 3-tab often only pre-pays the next repair. There remain sensible uses for it: a rental property, an outbuilding roof, or a house the owner expects to sell within a few years. For a house the owner intends to hold through ten years of Bay wind and summer hail, it is the wrong default.
Architectural shingles cover about three quarters of American homes, and Maryland roofs follow the same pattern. This thicker dimensional shingle is the product behind the $470–$670-a-square headline band, and its 110-to-130-mile-per-hour wind rating holds only when the crew follows the manufacturer’s high-wind nailing pattern. Plan on 20 to 25 realistic years from it in Maryland, not the 22 to 30 MyRoofData prints: humid summers age asphalt faster than dry ones, wind-driven rain tests every flashing lap, and the May-to-July hail peak bruises the mat. A roof that looks sound at year twelve can be a single tropical remnant away from a claim. AmeriPro, pricing Maryland in July 2026, puts architectural shingles at $5.50–$8.50 per square foot installed, which brackets the SmartRoofingCalculator band once the units are converted, and calls it the default it puts on most houses. That matches what the permit and insurance data suggest: architectural is the Maryland standard, and everything else in the table is measured against it.
The Class 4 upgrade gets its own section below, and in Maryland it deserves a cooler reading than it gets in hail-belt states. No Maryland-specific Class 4 premium was verified in this pass, and none is invented here. The table’s $500–$700-a-square band is modeled arithmetic: a Michigan insurance agent’s 2026 figure of roughly $30 more per square than standard architectural shingles, applied to the Maryland architectural band. On a 25-square roof, that arithmetic lands at $12,500–$17,500. The honest Maryland case for Class 4 rests less on hail — only 20 reports of two-inch hail in ten years statewide — and more on wind-driven debris, the FEMA hail risk rated Relatively High in Montgomery County, and the insurance discount, which is carrier-specific and must be confirmed in writing before the install. The section below works through all three.
Metal is where the per-year arithmetic flips the table, and where the Bay changes the specification. Ribbed panels with exposed fasteners run $605–$1,045 a square on MyRoofData’s Maryland model before tear-off — $15,125–$26,125 for a 25-square roof, lasting 30 to 40 years — and NumeralQ prices exposed-fastener metal on a 2,000 square foot roof at $15,620–$19,850. Standing-seam metal runs $930–$1,450 a square on SmartRoofingCalculator’s Maryland figures, or $23,250–$36,250, lasting 40 to 60 years, while MyRoofData prices it at $1,045–$1,760 a square before tear-off. Near tidal water, the metal itself matters as much as the seam: aluminum is the coastal choice because it does not rust, while steel relies on coatings that salt air attacks, and G.H. Clark prices the coastal-grade adder — aluminum panels plus stainless or coated fasteners — at $1,200–$3,500 on a Southern Maryland job. Its aluminum standing-seam range runs $13–$18 per square foot, or $26,000–$36,000, with 50 to 70 years of life. Snow slides off metal faster than off any asphalt, which matters in Garrett County. Hail does not bruise it the way it bruises a shingle mat. And standing-seam systems carry wind ratings of 140 miles per hour or more, well above what a nor’easter or a tropical remnant typically delivers in Southern Maryland. Run the per-year arithmetic and the table flips: at the midpoints, standing seam works out near $595 a year against architectural near $633. On the quote metal looks expensive, and on the calendar it looks cheap. Metal pricing is worked through in full in our metal roof cost guide, and the head-to-head numbers are in the metal vs shingles comparison.
Cedar shakes are a niche choice in Maryland: $990–$1,650 a square on MyRoofData’s figures, or $24,750–$41,250 for 25 squares, with 20 to 30 realistic years in this climate. Cedar looks beautiful on a wooded lot in the Piedmont and needs real maintenance, and it holds moisture in its gaps — a poor combination on a roof that has to survive humid summers, wind-driven rain, and a freeze-thaw winter in the same year. NumeralQ prices cedar on a 2,000 square foot roof at $18,780–$32,510, which sits below the 25-square table total because the job is smaller, not because the material is cheaper. Check the MyRoofData band against a local quote before budgeting around it, and ask the bidder how the shakes will be treated against the humidity.
Tile and slate occupy the luxury end of the table, and in Maryland their rarity owes as much to structure as to price. Tile runs $1,240–$1,860 a square on SmartRoofingCalculator’s figures, or $31,000–$46,500 for 25 squares, and slate runs $1,650–$3,300 a square on MyRoofData’s, or $41,250–$82,500. MyRoofData splits tile further: concrete at $1,100–$1,980 a square, clay at $1,320–$2,750. Each weighs far more than asphalt, each needs a structural check before it goes on, and each can serve for fifty years or longer. Tile’s Maryland problem is freeze-thaw in the west and wind uplift on the coast. A porous tile that soaks up autumn rain and freezes in a Garrett County January can spall. Slate’s problem is the crew and the district: few Maryland roofers lay slate regularly, and in Baltimore’s 30-plus historic districts the Commission for Historical and Architectural Preservation may review the visible slope. Slate laid by a crew that seldom handles it will find its first leak at the first thaw. Before pricing tile at all, read our tile roof cost guide: a Maryland frame needs its structure checked for concrete or clay weight first.
Read the table as an annual cost, not as a quote total. The yearly figures below come from dividing each midpoint total by the midpoint of its realistic life. At those midpoints, 3-tab works out near $707 a year, architectural near $633, Class 4 near $545, ribbed metal near $589, standing seam near $595, cedar near $1,320, tile near $775 at a 50-year life, slate near $550, and flat membrane near $825. They leave out the deductibles, where Class 4 and metal actually win, and the salt-air specification, where aluminum actually wins. Set the material table next to the insurance section when deciding. Neither one alone tells the truth. And remember that the flat-membrane row prices a 25-square roof that almost no Baltimore rowhome has: the rowhome section below re-prices membranes on the 12-to-18-square roofs they actually cover.

Roof Replacement Cost by Roof Size
Two Maryland listings can both read 2,000 square feet and still need roofs of completely different sizes. A single-story rancher puts roughly 2,000 square feet of footprint beneath its roof. A two-story colonial of the same living area covers only about 1,000 square feet of ground, so its roof surface runs about half the rancher’s. Once pitch, overhangs, and waste enter the calculation, that rancher footprint typically becomes 20–25 squares of roof surface. Confusing the listing’s living area with the roof surface is the pricing error Maryland homeowners make most often. It is not. Make every bidder print the square count as a separate line on the bid. A price built from living area prices a house that does not exist.
The table below runs on the SmartRoofingCalculator architectural band of $470–$670 a square, tear-off included, with the modeled Class 4 band beside it. The headline row is the 25-square one. The 20-square row carries the NumeralQ cross-check: the per-square band gives $9,400–$13,400, set against NumeralQ’s $10,110–$12,360 for a 2,000-square-foot roof statewide.
| Roof size | Typical Maryland home | Architectural shingle total | Class 4 shingle total |
|---|---|---|---|
| 15 squares | Small ranch / cottage | $7,050–$10,050 | $7,500–$10,500 |
| 20 squares | 2,000 sq ft ranch | $9,400–$13,400 | $10,000–$14,000 |
| 25 squares | Typical MD home | $11,750–$16,750 | $12,500–$17,500 |
| 30 squares | Large two-story | $14,100–$20,100 | $15,000–$21,000 |
| 35 squares | Large home, complex roof | $16,450–$23,450 | $17,500–$24,500 |
| 40 squares | Very large / steep | $18,800–$26,800 | $20,000–$28,000 |
Pitch is the first thing that makes this table stop applying. Crews move slower and stage differently on a 10/12 or 12/12 slope than on a walkable 4/12, and the per-square price rises with the difficulty. After pitch comes complexity. Every valley, dormer, skylight, and chimney adds a flashing detail that consumes crew time and becomes the first leak when rushed. Two roofs with identical square counts — one a plain gable, one cut up with dormers — still come out as two different prices. For a cut-up roof with several valleys, dormers, and hips, MyRoofData’s estimator adds roughly 15 percent to the labor. Third comes decking. Soft sheathing stays hidden until tear-off exposes it, and the crew prices its replacement by the sheet on the day. NumeralQ prices a 4-by-8 OSB deck sheet at $65.65–$94.37 installed in Maryland. Agree the per-sheet deck rate in writing while the old shingles are still on. The housing stock makes this more than a formality: 51 percent of Maryland homes were built before 1980, and the median Baltimore structure dates to 1946, so older roofs hide soft decking and extra layers more often than the quote assumes. A second layer to tear off costs $1.40–$1.84 per square foot on NumeralQ’s Maryland figures, and a house that already carries two layers cannot take a third: the code limit is two, and the job becomes a full tear-off.
Start the budget from measurements of the roof itself. Footprint times the pitch factor — near 1.12 at 6/12 on SmartRoofingCalculator’s chart, near 1.25 at 8/12 — plus 10 percent for waste on a simple gable and 15 percent on a hip roof, divided by 100 for squares. Line the bids up on square count first, and compare prices only after the counts agree. A bid that will not state its square count is a bid that cannot be compared with anything.
Roof Replacement Cost by City: Baltimore vs Columbia vs Rockville vs Annapolis vs Salisbury
Rockville is the puzzle in this table, so start there. It sits in the dearest labor market in the state, inside the Washington suburbs, and its verified NumeralQ figure — $9,960–$12,160 for a 2,000 square foot roof — is barely above Baltimore’s $9,790–$11,950. The planning models disagree with each other about the gap. Modernize prices the whole Washington-suburbs metro at $14,500–$25,000 for a 2,000 square foot roof, the highest band in the state. NumeralQ’s Rockville figure prices a standard job in a standard house, while Modernize’s metro band prices the larger, steeper, more complex roofs that fill Montgomery County’s subdivisions. Both can be right at once, because they are measuring different houses. What can be said honestly is the shape of the market: Rockville roofers earn about 5 percent above the national median, the highest verified city figure in the state, FEMA rates hail risk in Montgomery County as Relatively High, and the typical job is only 1.6 percent of the median Rockville home value — the smallest share in the state, because the houses are worth so much more than the roofs on them.
| City / metro | 2,000 sq ft roof (arch) | Roofer median wage | Market note |
|---|---|---|---|
| Baltimore | $9,790–$11,950 (NumeralQ) | $27.11/hr (metro) | Oldest housing stock, rowhome flat roofs, median structure 1946 |
| Columbia | $13,000–$22,000 (Modernize metro) | $27.11/hr (metro) | Inside Baltimore-Columbia-Towson; no city-only figure verified |
| Rockville | $9,960–$12,160 (NumeralQ) | +5% vs US median | DC suburbs; dearest labor; FEMA hail risk Relatively High |
| Annapolis | $13,500–$23,000 (Modernize metro) | Not published | Bay wind + salt air; JDH range $10,000–$25,000 |
| Salisbury | $11,500–$19,500 (Modernize metro) | $22.75/hr (metro) | Eastern Shore; cheapest roofer pay verified in the state |
Baltimore is the biggest roofing market in the state and the hardest to price with one number, because it contains two markets. The pitched-roof market runs $9,790–$11,950 on NumeralQ’s figures for a 2,000 square foot roof, while SmartRoofingCalculator’s Baltimore page, applying a local factor of 1.18 to the state baseline, prices a 25-square roof at $13,865–$19,765, or $555–$791 a square, and a 2,000 square foot roof at $11,092–$15,812. The flat-roof market is separate and cheaper per job, because the roofs are smaller: the rowhome section below prices it on its own terms. The roofer median wage in the Baltimore-Columbia-Towson metro is $27.11 an hour — about 2 percent above the national median — with 890 roofers employed. Baltimore’s permit picture is the quirkiest in the state, taken up in the permits section below: replacing shingles on a one- or two-family home sits on the city’s exempt list, while membrane replacements and deck work may not. And the city’s housing stock is the oldest in the state, with a median structure year of 1946, which means more deck work found at tear-off and more reason to get the per-sheet rate in writing first.
Columbia gets a warning label, not a verified city-only price. No NumeralQ or SmartRoofingCalculator figure for Columbia came out of this pass, and none is made up here. What can be said honestly is the shape of the market: Columbia sits inside the Baltimore-Columbia-Towson metro, which Modernize prices at $13,000–$22,000 for a 2,000 square foot roof, and inside the same $27.11-an-hour roofer wage market as Baltimore. Howard County’s planned subdivisions skew toward larger two-story colonials with cut-up rooflines, which is why the metro band runs above Baltimore’s city figure even though the wage is the same. AHI Roofing, blending Angi, Modernize, Fixr, and This Old House figures in November 2026, prices Baltimore and Columbia together at $13,000–$22,000 for a 2,000 square foot shingle roof — the same band, from a second source. Anyone getting quotes in Columbia should make at least one of them from a company with a permanent shop in Howard County. A warranty from a crew two counties away turns expensive the first time it is needed.
Annapolis prices like a coastal city because it is one. Modernize prices the Annapolis metro at $13,500–$23,000 for a 2,000 square foot roof, and AHI’s blended figures agree exactly. JDH Remodeling, which has installed Owens Corning roofs across Eastport, Heritage Harbour, and Hillsmere since 1986, prices most Annapolis jobs at $10,000–$25,000, with small ranches at $10,000–$14,000, mid-size colonials at $14,000–$25,000, and large premium homes at $25,000–$48,000 or more. The coastal specification is what moves an Annapolis quote: wind-driven rain and humidity punish weak flashing, salt air punishes the wrong metal, and upgraded underlayment and ventilation are worth more here than inland. No Annapolis-specific roofer wage was published in the BLS metro tables checked, and none is stated. The city’s historic districts add a second check: visible exterior work in a historic district may need review before the crew starts, and the quote should say who handles that.
Salisbury anchors the Eastern Shore at the low end of the state’s wage map. Modernize prices the Salisbury metro at $11,500–$19,500 for a 2,000 square foot roof, the second-cheapest metro band in the state, and the Salisbury metro roofer median is $22.75 an hour — about 15 percent below the national median, the lowest verified metro figure in Maryland, though only 30 roofers are counted in the metro. Eastern Shore rates run a tier below DC-suburb pricing on MyRoofData’s reading, and the wage line explains why. The Shore’s exposure runs the other way: coastal wind, salt air, and the tropical systems that arrive first on the Atlantic side of the Delmarva. A Salisbury quote should be read for its wind specification, not just its total. Frederick and Hagerstown complete the map on Modernize’s bands — $12,000–$21,000 and $11,000–$19,000 respectively for a 2,000 square foot roof — with Hagerstown the cheapest metro band in the state, reflecting western Maryland’s lower labor rates against its heavier snow.
Judge cities on price per square, never on the total: Annapolis at $23,000 looks dearer than Salisbury at $19,500, but the gap narrows once pitch, deck condition, and material are held equal. What actually differs between cities is exposure — Annapolis takes Bay wind and salt, Rockville takes the state’s highest hail risk, Baltimore’s rowhomes take a different roof system altogether, Salisbury takes coastal wind on the lowest wages in the state, and Garrett County takes snow no other part of Maryland sees — which is why the cheapest quote in the wrong market is the most expensive roof in the end.
Why Maryland Roofs Cost What They Do: Bay Wind, Salt Air & Two Winters
Three forces set what a Maryland roof costs, and they pull in different directions depending on which side of the Bay the house stands. The first is wind off the water, which prices the coastal specification. The second is salt air, which prices the metal and the fasteners. The third is the state’s split winter, which prices the west at a different level from the coast. What follows takes them in that order — wind first, because it reaches every county in the state, salt second, because it decides which metal survives, and winter third, because it decides how long whatever survives the wind will last.
The wind story starts with the tropical count. NOAA logged 35 tropical-storm and hurricane zone reports in Maryland over the ten years to 2025, and 76 tornado reports in the same decade. No single storm defines the Maryland roof the way a hurricane defines a Florida roof, and that is exactly the trap: the damage here arrives as remnants — a tropical system downgraded to a tropical storm, a nor’easter stalled off the coast, straight-line winds in a summer thunderstorm — and remnants still lift poorly nailed shingles. The design wind speed on the IRC wind map rises toward the coast, so a coastal Maryland roof may need high-wind shingles, more nails per shingle, and sealed starter courses, per SmartRoofingCalculator’s code notes. The baseline design wind speed is 115 miles per hour as a 3-second gust, and Montgomery County’s structural design data sets Risk Category II at 115 miles per hour. No Ocean City or coastal-specific design wind figure was verified in this pass, and none is stated. The rating’s real job is everything short of a tornado: straight-line winds and airborne debris riding in on the same system. The defense against those forces is a six-nail pattern rather than four, a high-wind starter course, and a shingle rated 110 to 130 miles per hour installed precisely to the manufacturer’s specification — with the nailing pattern spelled out on the quote. In a state where the hurricane deductible can apply statewide the moment a warning is issued for any part of it — the insurance section works through that rule — the nailing pattern is worth more than the shingle brand.
Salt air works slower than wind and costs more over time. Salt spray settles on every exposed piece of metal and keeps corroding it as long as it sits there. On a shingle roof, the metal is the flashing, the drip edge, the vents, and the fasteners — the parts that fail before the field of the roof does. On a metal roof, the metal is the roof. Aluminum does not rust, which is why it is the usual choice for homes right on the water, and why G.H. Clark prices coastal-grade aluminum panels with stainless or coated fasteners as a $1,200–$3,500 adder on a Southern Maryland standing-seam job. Steel panels rely on a protective coating, and many steel manufacturers limit or exclude finish warranty coverage for homes within a certain distance of salt water — read that part of the warranty before choosing steel near the Bay. Exposed-fastener metal is the weakest coastal choice: the screws sit in the weather, the washers age in the sun and salt, and one coastal inspector puts screw leaks at seven to ten years near salt water. That last figure is a single inspector’s field claim, flagged as such, but the mechanism behind it is not disputed: concealed fasteners under a standing seam keep salt away from the screw heads, and exposed fasteners do not. Whichever metal is chosen, the fasteners and flashings must be a compatible metal, because dissimilar metals in contact corrode the less noble one, and the small parts fail long before the panels do.
The winter split is the widest in any state this size. Baltimore takes about 20 inches of snow a season — the published figures run from 18.5 to 21.1 inches, and all three are printed in the research brief rather than one silently chosen — while Oakland, at nearly 2,400 feet, takes about 107 inches on the 1991–2020 normals, and Garrett County as a whole runs to 110 inches on the State Archives’ figures. The lower Eastern Shore takes about 10. The freeze-free period runs 130 days in Garrett County against 230 in southern Maryland and on the lower Eastern Shore. Ground snow load runs 15 to 30 pounds per square foot statewide on ASCE 7 mapping, with Montgomery County setting a 30-pound minimum by county amendment. In Garrett County, a roof holding snow all winter, carrying an ice dam at the eave, and absorbing freeze-thaw at every joint needs decking, underlayment, and ventilation all sized for that load. A roof on the lower Eastern Shore needs almost none of that, and needs the wind specification instead. The western winter gets its own section below, because a Garrett County roof is a different product from a Bay roof in everything except the shingle on top.
Hail is the fourth force, and the Maryland record is thinner than the damage in the hail-belt states but thicker than homeowners assume. NOAA recorded 352 reports of one-inch-plus hail over the ten years to 2025, ranking the state 33rd of 51, with 66 percent of large-hail reports landing between May and July. Only 20 reports of two-inch hail appeared in the decade, which is why NumeralQ judges impact-resistant shingles usually not worth it in Maryland on hail alone. That judgment deserves weighing, not blind acceptance: FEMA rates hail risk as Relatively High in Montgomery County, against Relatively Moderate in Baltimore city, and the hail that does most of the damage falls in the one-to-two-inch band, which is exactly the band where Class 4 shingles distinguish themselves. The Class 4 section below weighs the hail record, the wind-driven debris, and the insurance discount together, because no single one of them settles the question alone.
Beneath all three forces sits the labor market, which sets the price floor. Maryland roofers earn a median of $28.89 an hour, and the spread across the metros is wide: the Baltimore-Columbia-Towson metro at $27.11, Salisbury at $22.75, the Balance of State at $22.95, and the Philadelphia-Camden-Wilmington metro — which takes in Cecil County — at $28.72. The cheapest roofer pay in the state sits on the Eastern Shore, and the dearest sits in the Washington suburbs, which is the opposite of what a homeowner pricing a coastal roof would hope for. The season sets the calendar. Statewide, the roofing season runs April through October. The best installs land in the shoulder months — April and May ahead of the hail peak, September and October after the tropical season has wound down.

Baltimore Rowhomes & Flat Roofs: Membranes, Parapets & the CHAP Rule
If the house is a Baltimore rowhome, forget shingle pricing and shingle thinking entirely. The roof is flat or nearly flat, hidden behind a parapet wall, and the choice is a membrane system, not a shingle. Three membranes dominate Baltimore rowhome work: EPDM rubber, TPO single-ply, and modified bitumen. The roofs are small — a typical rowhouse roof runs 1,200 to 1,800 square feet, or 12 to 18 squares — so the totals run below the pitched-roof bands even though the per-square-foot prices run higher. Monarch Bay Renovations prices a typical Baltimore rowhouse roof at $6,000–$13,000. MarylandRoofPros prices rowhome flat and low-slope membrane replacement at $7,000–$18,000. BestRoofingEstimates prices a 14-square, 1,400-square-foot rowhouse roof at $7,700–$11,900 in EPDM, $9,800–$15,400 in TPO, and $9,100–$14,000 in modified bitumen. Angi, updated July 31, 2026, prices a 1,000-square-foot flat roof replacement in Baltimore at $6,000–$15,000, with an average of $5,476 across the projects it surveyed and most projects ranging from $3,065 to $7,987 — a lower average that reflects smaller scopes and partial work alongside full replacements, and should not be read as the price of a full membrane system.
The per-square-foot figures disagree across sources by enough to matter, and the disagreement is printed rather than averaged away. EPDM runs $8–$15 per square foot installed on Monarch Bay’s figures, $5.50–$8.50 on BestRoofingEstimates’, and $5.49–$8.48 on NumeralQ’s statewide figures. TPO runs $10–$18 on Monarch Bay’s, $7–$11 on BestRoofingEstimates’, and $6.66–$8.82 on NumeralQ’s. Modified bitumen runs $5–$9 on Monarch Bay’s, $6.50–$10 on BestRoofingEstimates’, and $5.30–$6.77 on NumeralQ’s. Angi’s Baltimore material bands — TPO $6–$11, EPDM $5.50–$10, modified bitumen $5–$9 — sit inside the same spread. The spread reflects different scopes: a membrane over sound decking with the old system left in place prices at the low end, while a tear-off down to the deck with rotted decking and soaked insulation hauled out prices at the high end. What the old roof hides is the swing factor, which is why an honest contractor inspects before quoting and why the quote should state the decking rate.
Each membrane buys a different combination of life and heat. EPDM is the black rubber membrane seen on countless Baltimore rowhouse roofs. It handles ultraviolet and freeze-thaw well and lasts 20 to 30 years or more when installed right, with 60-mil minimum thickness the specification to insist on. The trade-off is the black surface: it soaks up summer heat, which warms the top floor and runs up the air conditioning. TPO is the rising favorite in this climate. Its white, reflective surface bounces summer sun off the roof instead of into the house, which genuinely lowers cooling bills on a hot Baltimore third floor, and its seams are heat-welded into a continuous waterproof sheet. Lifespan runs 15 to 25 years on Monarch Bay’s figures, 22 to 30 on BestRoofingEstimates’ — the spread is flagged, and the honest reading is that TPO life depends more on the crew’s welding than on the membrane’s age. Modified bitumen, sometimes called mod-bit or torch-down, is the modern descendant of the old built-up tar-and-gravel roof. It is the budget-friendly option and installs in rolls with multi-ply redundancy, but it is more vulnerable to Baltimore’s freeze-thaw cycle and tends to last 15 to 20 years. Flat-roof pricing in full, including PVC and the national picture, sits in our flat roof replacement cost guide.
The rowhome roof has details no pitched roof has, and they are where the money goes. Parapet walls need flashing and coping that keep water out of the brick. Party walls are shared with the neighbours, so the membrane must tie into the adjoining roofs without creating a leak at the joint. Drainage runs through scuppers or internal drains rather than gutters, and a blocked scupper ponds water on a membrane that was never meant to hold it. Formstone fronts and cornices on the street face may fall under historic review. And access is the hidden cost: materials come up through the house or over the parapet on a tight city lot, with no driveway for a dumpster. A rowhome quote that prices only the membrane, with no line for parapet flashing, drainage, decking, and access, is a quote that will grow. Ask for each line separately, and ask how the crew will protect the neighbours’ roofs where the membrane meets the party wall.
One Baltimore rule catches more rowhome owners than any other. The Commission for Historical and Architectural Preservation — CHAP — reviews exterior alterations in more than 30 local historic districts across the city, including Mount Vernon, Federal Hill, Fells Point, and Bolton Hill. A flat membrane hidden behind a parapet usually escapes notice, but visible work on a front slope, a cornice, or a street-facing detail may need CHAP review before the crew starts. The quote should say who handles that review, and the schedule should allow for it. A roofer who has never heard of CHAP has never worked in a Baltimore historic district, and the house will pay for that education.
Class 4 Impact-Resistant Shingles in Maryland: What the Upgrade Costs and What It Pays Back
Start with the honest Maryland answer, because it differs from the hail-belt answer: in most of Maryland, Class 4 is a wind-and-debris upgrade with an insurance discount attached, not a hail upgrade. The hail record is real but thin. NOAA logged 352 reports of one-inch-plus hail over the ten years to 2025, with two-thirds of them between May and July, and only 20 reports of two-inch hail in the decade. NumeralQ, reading that record, judges impact-resistant shingles usually not worth it in Maryland. That judgment holds for a house in Baltimore city, where FEMA rates hail risk as Relatively Moderate. It holds less well in Montgomery County, where FEMA rates hail risk as Relatively High, and it holds least well for a house that has already taken one hail claim, where the next deductible is the number that matters. The upgrade should be priced on every asphalt quote and judged county by county, not adopted or dismissed statewide.
Here is the money, because the money is what settles this question. A typical Maryland deductible runs $500 to $5,000 for standard perils on the national pattern, and many policies now carry a separate, higher wind and hail deductible on top of that — sometimes a percentage of the dwelling value. Take a $300,000 home with a 2 percent wind deductible: the owner covers the first $6,000 of a wind claim before the insurer contributes anything. Set that exposure against the upgrade: about $750 on a 25-square roof at the modeled $30-a-square premium. One hail or debris event that a Class 4 roof rides out without replacement keeps one deductible in the homeowner’s pocket. That avoided payment runs $500 to $5,000 under a standard deductible and far higher under a percentage wind-and-hail deductible — against an upgrade priced near $750. A single claim the roof rides out can pay for the upgrade several times over. The payback is the deductible that never leaves the homeowner’s bank account.
Underwriters Laboratories ranks impact resistance on its UL 2218 scale, and Class 4 is the top of that scale. In the test, a two-inch steel ball falls twenty feet onto the shingle — about the size and speed of a golf-ball hailstone at terminal velocity. To pass, the shingle must survive the drop with no crack and no fracture. The flexibility comes from SBS-modified asphalt, a rubberized blend that stays pliable through a freeze and absorbs an impact rather than splitting. The Class 4 lines Maryland suppliers stock will be familiar names: GAF Timberline AS II, CertainTeed Landmark IR, and Owens Corning Duration STORM. No Class 4 shingle is hail-proof: a stone larger than the test ball damages any roof on the market. Most damaging hail in Maryland falls in the one-to-two-inch band, and that is exactly where Class 4 distinguishes itself — and where wind-driven debris from a tropical remnant or a nor’easter does the same work as hail, striking the roof at an angle the test never simulates.
This price is an explicit model, labeled as one. No premium figure specific to Maryland surfaced in this research, and this guide does not fabricate one. The number used here comes from a Michigan insurance agent’s 2026 figures, which put the upgrade near $30 per square above standard architectural shingles. Add that $30 to Maryland’s $470–$670 architectural band and the modeled Class 4 band becomes $500–$700 a square, or $12,500–$17,500 across 25 squares. National guides quote a steeper premium: 10 to 25 percent, or $1,000 to $2,500 on a typical house. Of the published figures, the Michigan agent’s $30 a square is the lowest. Treat the Maryland band as planning arithmetic, not as a verified Maryland price. Have the bidder write the actual premium on the quote.
A genuine discount exists, it varies by carrier, and it is worth less than the upgrade’s true value. Most major carriers offer some Class 4 discount against the wind-and-hail part of the premium. Those published ranges do not agree with each other, and the disagreement should be stated openly. The figures on record run from 5–20 percent in one source and 10–25 percent in hail-heavy states in another, to 15–20 percent from a Michigan agent and 20–30 percent in a national guide — all against the wind-and-hail portion only. The discount touches only the wind-and-hail portion, never the full premium, and each carrier sets its own figure. No carrier has published a figure specific to Maryland. Before signing, ask your own insurer to confirm the discount in writing, together with its qualifying product list and paperwork requirements. Until the carrier confirms it, a contractor’s discount figure is only a story. In Maryland, the bigger payback is the deductible that never gets paid, and in Maryland that stream matters most on the coast and in Montgomery County, where the hail risk and the wind exposure keep the deductible within reach of every homeowner.
Three rules close the section. First, name the product on the quote: manufacturer plus the exact shingle line. Second, keep the UL 2218 Class 4 marking — printed on each shingle’s back — with the job file. Third, secure the insurer’s discount confirmation and paperwork requirements in writing ahead of the install. Carriers may ask for photographs, a certificate, or an inspection; none accepts a contractor’s assurance alone. One warranty rule also applies: the extended warranty activates only through a credentialed crew, which is one more reason the lowest bid is not always the lowest-cost roof. The long-term owner, the house that has already had one hail claim, and the Montgomery County house under the Relatively High hail rating should treat Class 4 as the default, not the upgrade.
Snow, Ice Dams & the Western Winter: Garrett County on a Coastal-State Roof
Start from the ceiling stain. The stain shows up in March — a brown mark on the paint — by which time the dam behind it has been growing since January. The dam is not a shingle failure. It is an attic failure. Warm air leaking from the rooms below heats the underside of the roof deck through the attic. Snow over the warmed upper deck melts from underneath, while the snow above the cold eave stays frozen. That meltwater travels down past the warm wall line and refreezes where the deck turns cold, building a ridge of ice. With the ridge blocking its path, the next round of meltwater ponds behind it, slips under the shingles, and finds its way inside — through sheathing, down the wall, and into the ceiling. Often the brown March stain is the first anyone knows of it — or something worse. Even a newly installed roof can leak from a dam, because the shingles were never the weak point.
The snowfall behind that risk runs the widest gradient in any state this size. The lower Eastern Shore takes about 10 inches a season. Baltimore takes about 20. Oakland, at nearly 2,400 feet in Garrett County, takes about 107 inches on the 1991–2020 normals, and the State Archives puts the Garrett County ceiling at 110 inches. The record winter — 262.5 inches at Keysers Ridge in Garrett County in 2009–10 — is not a planning number, but it says something about what the western roof must survive. The freeze-free period tells the same story in days: 130 in Garrett County against 230 in southern Maryland and on the lower Eastern Shore. For snow load, ASCE 7 mapping puts the statewide range at 15 to 30 pounds per square foot, and Montgomery County’s amendment sets its own 30-pound floor. No Garrett-County-specific adopted snow-load figure was verified in this pass, and none is stated — the building department’s figure governs, and on a western roof it should be asked for by name. Low-slope porch roofs face double the danger, since shallow surfaces hold snow instead of shedding it, and a porch roof can end up carrying twice the load of the main slope. And the load builds through the season. Snow that falls in December packs down through January, turns to ice in February, and is still sitting there when March adds another foot.
Preventing a dam takes three layers of defense, and a reroof is the single job that reaches all three together. First comes the ice and water shield, a self-adhering membrane laid along eaves, through valleys, and around every penetration. It runs from the edge past the inside face of the exterior wall — at least 24 inches inside the wall line under IRC section R905.1.2, where the local climate table requires it. Maryland’s requirement is jurisdiction-by-jurisdiction, not statewide: in the colder and higher-elevation areas, the local Table R301.2 marks the ice barrier as required, and in the milder counties it may not. Do not let a contractor use that patchwork as an excuse to skip the membrane on a western roof. A single 36-inch roll seldom covers a deep eave or a shallow slope, so crews overlap two or three runs to reach six to nine feet of coverage. For a roof with a history of damming, a full-roof barrier is an option: NumeralQ prices whole-roof ice and water coverage at $0.91–$1.45 per square foot installed in Maryland. In Garrett County, where snow runs past a hundred inches a year, the membrane should run past the minimum on a low-slope roof, and the quote should state the distance in feet. The second layer is attic insulation combined with an air-sealed attic floor, so heat never reaches the attic to begin with. No Maryland-specific insulation R-value code requirement was verified in this pass, and none is stated — ask the building department for the local figure rather than trusting a number from another state. Third is balanced ventilation from soffit to ridge, holding the deck cold enough that the snow above it never melts from beneath. New shingles over a hot, airless attic will dam again by February, no matter whose name is on the bundle. All three layers belong in the reroof scope itself, not deferred to some later project.
Roofing through winter is feasible, but it follows rules of its own. Cold-weather installation works — SBS-modified shingles made it far more practical than it used to be — yet the sealant strips still need warmth to bond properly. Tabs left unsealed by hand in January will lift when the first spring wind arrives. Hand-sealing belongs in the written scope of any winter job, stated on the quote. Metal sheds snow quickest, and steeper pitches shed it better than shallow ones. A slab of snow sliding off metal can tear a gutter away, so snow guards above doorways should be quoted up front rather than added later. One last winter note for the Bay shore. The wind off the Chesapeake drives snow and rain sideways, and a Bay-facing slope takes weather a sheltered inland roof never sees. Spell out the flashing scope on a waterfront quote in full. Inspect a Bay-facing roof after the season’s first major November storm, rather than waiting for the first leak to appear.
Permits & Code: The 2021 IRC, the Baltimore Permit Exemption & the County Patchwork
The most surprising sentence in this section belongs first, because it catches the most homeowners off guard: in Baltimore City, replacing roof shingles on a one- or two-family home sits on the housing department’s Work Exempt From Permit list, alongside replacing roof tarring. No building permit is needed for that scope. The same list does not establish a blanket exemption for every roof job in the city. A membrane roof replacement, decking replacement, structural repairs, and changes to the roof’s framing or drainage can each trigger a permit, and work in a historic district may need separate review. The Baltimore City rule is not the state rule, and it is not the rule in Baltimore County, Carroll County, or Prince George’s County. Only the building department can state the figure that governs; a contractor’s guess does not.
The statewide code picture is a state standard with local enforcement. Baltimore City’s Building Code adopts the 2021 International Building Code and the 2021 International Residential Code, with the Maryland Building Performance Standards modifications. Statewide, the Maryland Building Performance Standards are modeled on the 2018/2021 IRC with local amendments, and each jurisdiction enforces its own version. The code sets the design wind speed baseline at 115 miles per hour as a 3-second gust, with higher speeds toward the coast on the IRC wind map. It sets the two-layer limit: if two layers of shingles already exist, the job is a full tear-off, not a recover, under IRC section R908.3.1.1. And it sets the ice-barrier rule where the local climate table requires it — a self-adhering membrane from the eave edge to at least 24 inches inside the exterior wall line, under IRC section R905.1.2. The snow-load table runs 15 to 30 pounds per square foot on ASCE 7 mapping, with Montgomery County’s 30-pound minimum set by county amendment. The code that governs a specific house is the version the local jurisdiction adopted, with its own amendments, and the building department is the only source that can state it.
Permit rules vary county by county, and the published summaries disagree with each other, which is itself worth knowing. Baltimore County requires a permit when 50 percent or more of the sheathing or deck is being replaced, and requires permits for any work in historic districts, the floodplain, the Chesapeake Bay Critical Area, or on the Landmarks List, regardless of scope. Carroll County takes the opposite approach: re-roofing and re-siding need no permit, but the work must still meet the adopted codes and all manufacturer requirements, and structural member replacement needs a permit. Prince George’s County requires permits for roof replacements and inspects afterward, through the Department of Permitting, Inspections, and Enforcement. Talbot County requires permits for full replacements through its OpenGov system, while exterior shingle repairs generally do not need one. Anne Arundel, Montgomery, and Howard counties each run their own requirements and fee structures. MyRoofData’s summary — permits required in all counties — is overbroad against the Baltimore City exemption and the Carroll County rule, and is flagged here rather than relied on. A 2022 contractor blog claiming no permit is required anywhere in Maryland for a roof replacement is outdated and overbroad, and is not relied on at all.
Permit fees vary just as widely, and the published numbers disagree by a factor of three, which is itself worth knowing. SmartRoofingCalculator puts the Maryland permit at about $320, typically $200–$500. MyRoofData puts it at $100–$400. RoofingEstimatorPros puts it at $250–$800, and $300–$900 in Baltimore. HomeQuoteHQ puts Baltimore at $175–$400. NumeralQ, working from city fee schedules, found no priceable re-roof permit figure published for Baltimore or Rockville on a $15,000 job, and prints “not published” rather than a guess. Each of those figures is printed above, and none of them settles the question for a particular house — the building department’s figure does. The pattern is what matters: a permit is a minor line on a major job, and it buys the homeowner an inspection and a paper record.
Small repairs almost never need a permit, the one permit rule that holds everywhere from Ocean City to Oakland. A full re-roof needs one in most places, with Baltimore City shingle replacement and Carroll County re-roofing as the notable exceptions above. That inspection quietly protects the owner: nailing pattern, ice barrier where required, flashing, and ventilation all get checked, and the resulting record is something the next buyer’s inspector and the next underwriter will both request. Stormwater rules add one more Maryland wrinkle: SmartRoofingCalculator notes that stormwater regulations sometimes require gutter upgrades during a reroof, so the gutter line on the quote deserves a question, not an assumption. Gutter work is priced on its own in our gutter installation cost guide.
Hiring a Roofer in Maryland: The MHIC License, the One-Third Deposit & the Guaranty Fund
Maryland’s hiring picture can be stated in one sentence: the state licenses no roofers, and licenses every roofing contractor. There is no roofer-only license in Maryland. Roofing work on an existing home is home improvement, so the contractor needs a license from the Maryland Home Improvement Commission — the MHIC — under the Maryland Department of Labor. The license requires at least two years of experience in home improvement work or equivalent education, a passing score of 70 percent on the PSI-administered exam taken before applying, proof of financial solvency, and at least $500,000 in general liability insurance, a minimum that rose from $50,000 effective June 1, 2024. There are no license classes, no trade specialties, and no reciprocity with any other state. The same license covers a $900 repair and a $900,000 renovation. The license number must appear on contracts and advertising. A contractor who cannot show an MHIC number is a contractor who cannot legally do the job.
Because the license is general rather than roofing-specific, the screening has to go further than the number. Apply the same five vetting steps to each bidder, in every county. The first is the MHIC lookup itself: search the contractor’s name or license number on the Maryland Department of Labor’s license lookup page, and confirm the license is current — never take a number printed on a truck at face value. The second is insurance: general liability of at least $500,000, proved with a certificate the carrier mails to you directly, with the business name matching the contract, plus workers’ compensation for the crew. Third, a permanent Maryland address plus a local phone number that predates the most recent storm. Fourth, three references from within your own county, with street addresses worth visiting. Fifth, manufacturer certification where it matters: credentialed installer status with GAF, Owens Corning, or CertainTeed. The extended warranty activates only in a credentialed crew’s hands. Close with three written quotes built on one identical spec sheet, so all three prices describe the same roof. Our questions to ask a roofer guide carries the full interview list, and an inspection before the quotes arrive tells the bidders what they are pricing.
Behind those five steps sit two Maryland consumer protections, both worth knowing by their statute numbers. The first is the deposit cap: a home improvement contractor may not take a deposit of more than one-third of the contract price, under Business Regulation section 8-617(b), and one source adds that no payment may be accepted before the contract is signed. A contractor asking for half up front is asking for something the law forbids. The second is the Home Improvement Guaranty Fund, financed by contractor license fees, which compensates homeowners for actual losses from unworkmanlike, inadequate, or incomplete work by a licensed contractor. The cap carries a conflict that belongs in the open: current statute-citing sources put the maximum at $30,000 per claimant or the amount the homeowner actually paid, whichever is less, up to $250,000 total against one contractor, while older sources put it at $20,000 per claimant and $100,000 per contractor. This guide uses the $30,000 figure with the conflict flagged. The critical limitation has no conflict at all: only work by a licensed contractor qualifies. Hire someone without an MHIC license and the fund is closed entirely, whatever the cap.
The teeth behind the license are criminal, not just administrative. Performing or offering home improvement work without an MHIC license is a misdemeanor under Business Regulation section 8-601. A first conviction carries a fine of up to $1,000, up to 30 days in jail, or both. A second or subsequent conviction carries a fine of up to $5,000, up to two years in prison, or both. An unlicensed contractor can also lose the ability to enforce the contract or collect payment. MyRoofData’s Maryland page puts the practical point bluntly: MHIC licensing is strictly enforced, verify the number before signing, because unlicensed contracting is a criminal offense and correlates strongly with bad workmanship. The MHIC license does not cover new-home construction, which runs through the Home Builder Registration Unit, or purely commercial work, which follows a separate county route. For a reroof on an existing Maryland home, the MHIC number is the credential, and there is no substitute for it.
After a tropical remnant or a hail outbreak, Maryland turns into storm-chaser territory, and the crews arrive within days, knocking on doors across the damaged neighborhoods. Some are legitimate traveling crews. Many are not. The storm-chaser pattern is recognizable on sight, every time it appears. A knock and a contract pushed across the threshold, an out-of-state number, no office in town, no MHIC number on the paperwork, a promise to make the deductible disappear, and a demand for a large payment before any work starts. Watch for a door knock pushing an agreement to sign on the spot. Out-of-state phone numbers, no permanent local office, no MHIC license, a promise to waive or absorb your deductible, and a demand for more than the one-third deposit the law allows.
A thorough Maryland quote identifies the manufacturer, the exact shingle line, and the underlayment type. It also names the ice and water shield coverage in feet from the eave, where the membrane is required or specified. Drip edge, ventilation scope, nailing pattern, tear-off depth, per-sheet deck rate, disposal, and cleanup all belong on the same document. Each bid should total its own surface, allowing square-for-square comparison between bidders. Manufacturer years and workmanship years are separate promises, and each needs its honoring party named. Every bid should carry three code-driven items. A bid missing any of them is a red flag. Those three: ice and water shield along eaves, valleys, and penetrations — at least 24 inches inside the exterior wall line where the local table requires it; drip edge at eaves and rakes; and a six-nail high-wind fastening pattern where Maryland wind runs hardest. A bid with no ice barrier on a Garrett County roof means a leak in February. A bid with no high-wind pattern on a Bay-facing roof means lifted tabs in the next nor’easter. And one last check before the work starts: ask for insurance and workers’ compensation certificates mailed straight from the carrier, with the business name matching the contract — and confirm that the MHIC license is current on the Department of Labor’s lookup, not just printed on the quote.
Insurance: Hurricane Deductibles, ACV vs RCV, the Roof-Age Rule & the Mitigation Discount
A Maryland homeowner’s insurance policy is the part of the roof that either earns its keep or delivers a nasty surprise, and in this state the surprise usually has a hurricane warning attached to it. Three studies price Maryland coverage from different angles, and their premium figures disagree — a disagreement worth stating outright. NerdWallet, on May 6, 2026, prices Maryland homeowners insurance at $2,375 a year for a $400,000 dwelling, against a national average of $2,490 — the state a little cheaper than the country. MoneyGeek, on June 19, 2026, prices the same state at $2,633 a year, ranking it 31st of 51 jurisdictions and about 26 percent below its national average of $3,548, on a $250,000 dwelling profile; its updated pages put the figure at $2,623. InsuranceQuotes, on rates as of September 30, 2026, prices Maryland at $3,146 a year for a 2,000 square foot wood-frame house with a composition roof, built in 1997, insured for $300,000 with a $1,000 deductible and a 2 percent hurricane deductible — about 1.5 percent above the 50-state average for the same house. The three studies measure different dwelling values and different profiles, and the spread between them is the point: no single average describes a specific Maryland house. Measure every figure in this section against the policy on your own house. Two Maryland facts sit behind all three studies: the state prohibits insurers from using credit scores to set home insurance rates, and homes built in 2020 cost $1,669 a year to insure on MoneyGeek’s figures against $2,870 for 1980 construction — age is priced into the premium whether the roof is new or not.
The hurricane deductible is the Maryland rule that most homeowners first hear about from the adjuster standing in the driveway. Maryland is one of nineteen states plus the District of Columbia with hurricane deductibles, per the Insurance Information Institute. Maryland law — Insurance Article section 19-209, as amended by Chapter 491 of 2016 — allows a mandatory percentage hurricane deductible to apply to the entire state if a hurricane warning is issued for any part of it. The deductible applies only from the time the National Hurricane Center issues a hurricane warning for any part of Maryland until 24 hours after the last warning ends, and it applies regardless of where the insured home sits in the state. A warning for Ocean City can trigger the percentage deductible on a house in Oakland. A mandatory deductible may not exceed 5 percent of the Coverage A dwelling limit unless the insurer has filed an underwriting standard with the Maryland Insurance Administration. Percentage deductibles typically run 1 to 5 percent of the insured value. On a $300,000 dwelling, 2 percent is $6,000 out of pocket before the insurer pays anything on a wind claim, and 5 percent is $15,000. Read the declarations page peril by peril, before the storm, not after it. The same law requires insurers to offer a premium discount to homeowners who submit proof of qualified wind-mitigation repairs or improvements, inspected by a licensed contractor — a discount that can reward exactly the high-wind nailing pattern and sealed starter course the coastal specification already calls for. Ask the carrier what proof it wants, and get the discount in writing.
A $500-to-$5,000 standard deductible for most perils is what most policies carry on the national pattern, with a separate, higher deductible for wind and hail damage now appearing on many policies. Per the Insurance Information Institute, lifting a deductible from $500 to $1,000 usually trims the premium by 10 to 25 percent — genuine savings, and a genuine gamble on the next storm. Give the declarations page a careful read while the weather is calm, not after damage has happened.
The roof-age rule is what makes the call different as the roof gets older. Roofs younger than ten years generally attract the best rates. In the ten-to-twenty-year window, expect the carrier’s standard rate. Past twenty years, roofs often draw surcharges, steeper wind-and-hail deductibles, or outright refusals to quote. Certain carriers now decline new business outright when the roof is twenty years old or older. Depreciated actual cash value — or a roof payment schedule — is how many carriers settle an older roof, instead of replacement cost. Fifteen years in, depreciation has halved the value of a $20,000 roof. Subtract a $2,000 deductible and the payout nets roughly $8,000. The homeowner covers $12,000 or more from their own pocket. No Maryland-specific carrier trigger was verified in this pass, and none is stated — the ages above are the industry pattern, labeled as such. Confirm the policy type and the roof-age trigger while the sky is still clear. At renewal time, few actions matter more than documenting a replacement with its permits and receipts.
The policy’s settlement basis — replacement cost value or actual cash value — is the other figure to pin down. With replacement cost coverage, the insurer funds a new roof regardless of the old roof’s age, minus the deductible. Actual cash value works in reverse, valuing the roof as it stood at the moment of damage — new-roof cost minus depreciation — and shingles depreciate quickly. No regulator published the worked example below; this guide calculated it. Its inputs are a $14,250 roof (the midpoint of Maryland’s architectural band), a $2,000 flat deductible, and straight-line depreciation at 2 percent a year across a 25-year shingle life.
| Roof age | RCV payout | ACV payout |
|---|---|---|
| 5 years | $12,250 | $10,825 |
| 10 years | $12,250 | $9,400 |
| 15 years | $12,250 | $7,975 |
| 25 years | $12,250 | $5,125 |
Five years after installation, the ACV check falls $1,425 short of replacement cost. The gap widens to $2,850 at ten years and $4,275 at fifteen; at twenty-five, the policy pays $5,125 toward a $14,250 roof, barely over a third of the cost. With an ACV policy, the homeowner is effectively self-insuring an older roof, knowingly or not. Check the policy type before the storm. Beyond ten years under ACV, the insurer contributes little toward either a Class 4 upgrade or a replacement. Both decisions look different. After twenty years, with the policy moved to ACV, the replacement calculus shifts. The carrier will fund little of a repair or a replacement at that stage, while a new roof restarts the clock entirely.
Claims follow a sequence, and the sequence matters. Photograph all damage before anyone disturbs it — each slope, each gutter, each dented vent cap — and date every photograph. The adjuster inspects first and the contractor estimates second, because an estimate written before the inspection is a number without a claim behind it. Refuse outright any contingency or assignment-of-benefits agreement presented in the driveway. Obtain the adjuster’s written report, then compare its line items against the contractor’s estimate one by one. File the paperwork: Class 4 product name, UL 2218 marking, install photos, and the mitigation inspection the discount requires. Whether next year’s discount materializes comes down to evidence of what the roof is made of.
The Class 4 discount exists, varies by carrier, and applies only to the wind-and-hail portion of the premium. Depending on the source, published ranges span 5–20 percent at the low end to 20–30 percent at the high end. Get your own carrier’s figure in writing before installation, along with its qualifying product list and required paperwork. Until the carrier confirms it, a promised discount remains only a promise. And the mitigation discount is separate from the Class 4 discount: Maryland law requires the carrier to offer a discount for qualified wind-mitigation work inspected by a licensed contractor, so a coastal roof fitted to the high-wind specification may earn two discounts, not one. Ask about both, in writing, before signing.

Paying for It: No Federal Credit in 2026, HEAR Not Launched in Maryland & No Roof Rebate
Maryland is a state where the federal home-energy rebate programs have not launched — and that distinction changes nothing about a roofing quote, which is the point of this section. The Maryland Energy Administration resubmitted the state’s HEAR and HOMES applications to the Energy Department on September 30, 2026, under updated guidance. No launch date has been set, and applications are not open, as verified in early November 2026. Once operating, HEAR will pay as much as $8,000 to income-qualified households at or below 150 percent of area median income — and under Energy Department Notice 26-2, dated May 29, 2026, only electric-to-electric upgrades qualify. Under HOMES, the general cap is $4,000, while households at or below 80 percent of area median income can receive up to $8,000. But HEAR never pays for a roof. No lease or pass-through arrangement on record steers federal money toward a Maryland roof, this research found no state roof grant, rebate, or tax credit, and no utility roof rebate surfaced either. NumeralQ, checking in October 2026, records the state roof grant as none found. A homeowner combining a reroof with a heat pump should keep the two prices apart: the roof is paid from the homeowner’s pocket, while the heat pump might qualify for HEAR after Maryland’s program opens. The rebate half of that decision is priced in our heat pump cost in Maryland guide. Modernize mentions a Maryland Department of Housing repair program as something to ask about; whether it covers roofs was not verified in this pass, and no promise is attached to the mention. Ask, and get the answer in writing.
The federal tax credit has ended, and the cutoff dates decide everything. Property placed in service after December 31, 2025 earns nothing from either credit: neither the 30 percent Residential Clean Energy Credit (§25D) nor the Energy Efficient Home Improvement Credit (§25C). The One Big Beautiful Bill Act (Public Law 119-21), signed July 4, 2025, ended both credits; IRS Fact Sheet FS-2025-05 confirms the cutoff date. Under that Act, both credits stop for any install placed in service after December 31, 2025. Shingles and membranes were never solar equipment in the eyes of the credit. For a bare roof with no solar equipment, the solar credit never applied at all. Section 25D covers solar equipment only, so roofing work never qualified under it. A few roofing materials did qualify for claims under §25C in earlier years. That door is closed too. If a 2026 quote still shows a tax-credit line, the contractor priced the job under a law that no longer exists. Ask the contractor to remove it and re-price the job. A federal tax-credit line has no place on any 2026 quote. A roof installed in 2026 leaves nothing to claim. Our federal energy tax credits guide carries the full cutoff dates and the programs that survived.
The §48E commercial clean-electricity credit reaches solar arrays and similar clean-electricity equipment — and nothing that sits on a roof as roofing. Maryland homeowners who need help funding a 2026 roof have two honest routes: a home-equity loan or a contractor financing plan. Compare the annual percentage rate first; the monthly payment comes second. The money comes from the insurer. A Class 4 roof can earn a discount on the wind and hail portion of the premium, a high-wind specification can earn the mitigation discount Maryland law requires carriers to offer, and every claim the roof rides out saves a deductible. The insurer is what pays toward a roof, through the Class 4 discount, the mitigation discount, and the avoided deductible. A homeowner weighing a solar array under the new roof should read our solar panel cost in Maryland guide before signing either contract, because the §48E pass-through only reaches a leased solar array, never the roof underneath it, and because detaching and resetting panels for a later reroof runs $1,500–$5,000. Financing terms, dealer fees, and the loan-versus-equity choice are worked through in our how to finance a new roof guide.
Repair vs Replace & Getting Quotes in Maryland: The Decision Rules and the Checklist
When the roof is still early in its life and the damage stays local, patching it beats tearing the whole thing off. Imagine a roof under ten years old: a handful of shingles gone, one chimney flashing leaking, a few tabs lifted by wind. A targeted fix is the right answer there, not a full replacement. NumeralQ’s Maryland repair figures, priced October 26, 2026, set the scale: $237–$510 for a flashing repair, $318–$890 to find and fix a leak, $329–$720 for a chimney reflash, and $339–$670 for a skylight leak. Modernize puts Maryland minor repairs at $400–$950 and major repairs at $1,250–$1,800, and AHI Roofing puts most Maryland repairs at $400–$1,800 with a typical repair near $1,100. A Southern Maryland contractor’s sold jobs run higher, with repairs at $1,200–$3,600 and a $1,000 minimum, and a written rule: if the repair costs 35 percent or more of the replacement, the firm will not repair the roof. The spread between the price lists and the ledger is the difference between pricing the part and pricing the job. Our roof repair cost guide prices repairs separately — patching, partial replacement, and the threshold where repair stops making sense on a Maryland roof.
Any of three signals — age, spread of damage, or plain arithmetic — can point toward replacement. When architectural shingles are past fifteen years and wind has lifted over a quarter of the slopes, replacement beats repair. A lifted mat patched over is cosmetic work only; the next storm defeats it regardless. Soft decking or delaminated sheathing also means replacement: structure is replaced, never patched. When dams keep returning each winter even after the attic has been insulated and ventilated, the failure is systemic — the shingle is not the problem. An insurer-funded claim on a roof old enough that the following claim would pay ACV at a third of the cost argues the same way: accept replacement money while it remains available. A roof nearing the carrier’s twenty-year trigger is also a replacement candidate, with the policy nearing ACV and renewal nearing refusal. When a repair quote exceeds about a third of the replacement quote and the roof holds under five years of life, replacement wins again. On a Baltimore rowhome, add one more trigger: a membrane that ponds water after every rain, with seams opening at the parapet, has reached the end of its system life even if the field still looks sound.
Checking twice a year keeps this decision out of panic territory. Use the fall check to catch summer wind and hail damage before the adjuster’s window closes. Spring is for checking what winter did: ice-dam and freeze-thaw damage on a western roof, salt and wind damage on a Bay roof, caught before the May-to-July hail peak stacks a second round of trouble on top. After several Maryland winters and summers, a roof can look solid from the curb while standing far nearer failure than it appears. Bruising starts inside the mat and stays out of sight until the shingle itself splits.
Ten items, in the order to use them. Miss one, and the quote being signed has not truly been read.
- Roof measurements in writing. The bid prints square count, pitch, and waste allowance — pricing from the listing’s living area is not acceptable.
- Material named by manufacturer and line. GAF, CertainTeed, or Owens Corning, with the exact shingle line and the Class 4 UL 2218 marking where the upgrade is priced; aluminum specified by alloy on a coastal metal roof.
- Tear-off depth stated. One layer or two, and the per-sheet deck replacement rate agreed before the old shingles come off — NumeralQ prices a 4-by-8 OSB sheet at $65.65–$94.37 installed in Maryland, and the rate on the quote is the number that counts.
- Membrane distance from the eave, stated in feet. At least 24 inches inside the exterior wall line under IRC R905.1.2 where the local table requires it, further where the eave runs deep or the slope runs shallow, and six to nine feet on a low-slope western roof.
- Drip edge, airflow, and fastening pattern all specified. Drip edge at eaves and rakes, balanced soffit-to-ridge ventilation, and the six-nail high-wind pattern on Bay-facing and coastal slopes.
- MHIC license verified on the Department of Labor lookup, and insurance certificates mailed straight from the carrier. Business name matching the contract, general liability of at least $500,000, workers’ compensation for the crew — never a certificate the contractor hands over.
- Deposit no more than one-third, and three local references checked. The one-third cap is the law under Business Regulation section 8-617(b); the references come from your own county, with street addresses to visit, and a permanent Maryland address and local number in service since before the last storm.
- Three written quotes, one shared specification. One spec, three bidders, so the prices compare the same roof — and the permit question answered by the building department, not the bidder, since the answer varies by county.
- Zero federal credit line, zero HEAR rebate line. $0 in 2026 for the credit, and HEAR has not launched in Maryland but never covers roofing in any case.
- Insurer’s Class 4 and mitigation discounts confirmed in writing first. Qualifying product list and paperwork included, before the install — a promised discount is not a discount until the carrier confirms it, and Maryland law requires the carrier to offer the mitigation discount on inspected wind-mitigation work.

Sources & methodology
Every price in this guide carries its source and its date, and every number this guide worked out itself is labeled as its own arithmetic. The 25-square material totals, the size-table figures, the Class 4 totals, and the cost-per-year figures are NestPriced’s own calculations from the cited per-square ranges and lifespans, worked out by dividing each midpoint total by its midpoint realistic life. The RCV/ACV worked example in the insurance section is our own calculation too, built on a $14,250 roof, a $2,000 flat deductible, and straight-line depreciation of 2 percent a year over a 25-year shingle life. They are realistic figures worked from the climate, not numbers lifted from one published table. Where two sources disagree, both are printed and the disagreement is flagged rather than settled silently.
- Headline prices: SmartRoofingCalculator Maryland state page (page dated Apr 24, 2026; index updated Nov 9, 2026): architectural shingles $470–$670/sq fitted with tear-off; 25-square roof $11,750–$16,750; standing seam $930–$1,450/sq; tile $1,240–$1,860/sq; permit ~$320 ($200–$500); roofer median $25.00/hr (May 2024 BLS vintage); state factor 1.035; Maryland ranks 39 of 50 cheapest-to-most-expensive; neighbours Pennsylvania $440–$640, Delaware $430–$620, Virginia $430–$620, West Virginia $390–$560 per square; Baltimore page (local factor 1.18): 25-square $13,865–$19,765 ($555–$791/sq), 2,000 sq ft roof $11,092–$15,812.
- NumeralQ Maryland (pricing Oct 26, 2026): 2,000 sq ft roof statewide $10,110–$12,360; Baltimore $9,790–$11,950; Rockville $9,960–$12,160; sizes 1,000 sq ft $5,340–$6,600 to 3,000 sq ft $14,880–$18,110; material table for a 2,000 sq ft job — 3-tab $8,360–$9,930, architectural $10,110–$12,360, modified bitumen $11,170–$14,400, EPDM $11,540–$17,810, designer $12,020–$14,520, TPO $13,890–$18,490, exposed-fastener metal $15,620–$19,850, standing seam $22,360–$33,650, natural slate $34,320–$65,470; add-ons — extra layer $1.40–$1.84/sq ft, deck sheet $65.65–$94.37, whole-roof ice and water barrier $0.91–$1.45/sq ft, gutters $8.85–$12.62/linear ft, chimney/wall flashing $358–$509, skylight reflash $526–$679; roofer median $28.89/hr (BLS May 2025), billed $58–$75/hr; hail 352 reports of 1 in+ 2016–2025 (33rd of 51), 66% May–July, 20 reports of 2 in hail; tornado reports 76; tropical zone reports 35; no state roof grant; 51% of homes built before 1980; Baltimore roofer pay +2% vs US median, Rockville +5%; FEMA hail risk Relatively High in Montgomery County, Relatively Moderate in Baltimore city.
- MyRoofData Maryland (2026 model): typical single-family architectural roof $14,250–$24,500, about 10% above the national average; crews $60–$100/hr; state cost index 1.10; tear-off $100–$200/sq/layer; permits $100–$400; material table per square before tear-off — 3-tab $385–$605, architectural $495–$825, ribbed metal $605–$1,045, standing seam $1,045–$1,760, cedar $990–$1,650, concrete tile $1,100–$1,980, clay tile $1,320–$2,750, natural slate $1,650–$3,300, flat membrane $605–$1,045; cut-up roof adds ~15% labor.
- Modernize (updated Aug 27, 2026): Maryland average ~$14,000, most projects $9,000–$22,000; materials ~$8,500, labor ~$5,500; $6–$11/sq ft, $600–$1,100/sq; metro bands for a 2,000 sq ft roof — DC suburbs $14,500–$25,000, Baltimore-Columbia-Towson $13,000–$22,000, Annapolis $13,500–$23,000, Frederick $12,000–$21,000, Salisbury $11,500–$19,500, Hagerstown $11,000–$19,000; metal $10–$20/sq ft, $18,000–$45,000, standing seam 2,000 sq ft $22,000–$40,000. Modernize repair page (Oct 12, 2026): Maryland minor repairs $400–$950, major $1,250–$1,800.
- RoofingEstimatorPros (updated Aug 26, 2026): 2,000 sq ft architectural roof $15,881–$28,361, average $21,428, about $10.71/sq ft including tear-off, permits and waste; permit range $250–$800; Baltimore $16,810–$29,914, average $22,634, permit $300–$900 — flagged as the high outlier.
- Angi Baltimore (updated May 28, 2026): shingle roof average ~$10,973, range $7,838–$25,080; labor ~$6,580, nearly 60% of the total. Angi flat roof Baltimore (Jul 31, 2026): 1,000 sq ft flat roof $6,000–$15,000; average $5,476, range $3,065–$7,987; TPO $6–$11/sq ft, EPDM $5.50–$10, modified bitumen $5–$9.
- HomeYou Baltimore (Sep 3, 2026): $10,448–$21,151, average $13,841. HomeCostLens Baltimore (Sep 2026): average ~$11,500, range $9,410–$18,810; labor ~$29/hr. HomeQuoteHQ Baltimore: average $11,200, range $8,200–$16,500; permit $175–$400; median structure year 1946; ~1,420 roofers in Baltimore-Columbia-Towson, average $52,380/yr.
- SquareDash (Apr 2026): Baltimore average $15,200 fixed price, 2,000 sq ft home.
- Monarch Bay Renovations, Baltimore (2026 guide): Baltimore metro asphalt $8,000–$16,000, ~$4–$7/sq ft; rowhouse flat roof (1,200–1,800 sq ft) $6,000–$13,000; EPDM $8–$15/sq ft, 20–30+ yrs; TPO $10–$18/sq ft, 15–25 yrs; modified bitumen $5–$9/sq ft, 15–20 yrs.
- JDH Remodeling, Southern Maryland (1,460+ inspections, 2024–2026): Maryland $9,500–$20,000 most homes; colonial $9,500–$15,000; townhome/rancher $5,500–$8,500; baseline asphalt $4.50–$7.00/sq ft of roof surface; Prince Frederick colonial $14,900 (2026); Annapolis $10,000–$25,000; repairs $1,200–$3,600, $1,000 minimum, 35% rule.
- AHI Roofing (Nov 3, 2026, blending Angi/Modernize/Fixr/This Old House): most Maryland asphalt jobs $8,000–$25,000; Annapolis/Anne Arundel $13,500–$23,000; Baltimore/Columbia $13,000–$22,000 (2,000 sq ft). AHI repair guide (Nov 10, 2026): most repairs $400–$1,800, typical ~$1,100.
- AmeriPro (Maryland, July 2026): 3-tab $4.50–$6.50/sq ft; architectural $5.50–$8.50/sq ft; designer $8.50–$14/sq ft; most full replacements $9,000–$28,000; average MD roof 20–35 squares.
- MarylandRoofPros (2026 planning ranges): architectural asphalt $12,000–$32,000, ~$500–$900/sq; rowhome membrane $7,000–$18,000; small repair $325–$800.
- G.H. Clark, Southern Maryland (2026): standing seam $14,000–$28,000; aluminum standing seam $13–$18/sq ft, $26,000–$36,000, 50–70 yrs; coastal-grade adder $1,200–$3,500; wind ratings 140+ mph.
- BestRoofingEstimates, Baltimore: rowhouse 14-square roof — EPDM $7,700–$11,900 ($5.50–$8.50/sq ft), TPO $9,800–$15,400 ($7–$11/sq ft), modified bitumen $9,100–$14,000 ($6.50–$10/sq ft); 60-mil minimum EPDM; 30+ CHAP historic districts.
- Snowfall: Maryland State Archives (May 27, 2026) — average seasonal snowfall 20.6 in; 10 in lower Eastern Shore to 110 in Garrett County; record 262.5 in at Keysers Ridge, 2009–10; average precipitation 43.6 in; freeze-free period 130 days Garrett County to 230 days southern Maryland/lower Eastern Shore. Oakland ~107 in/yr (USClimateData, 1991–2020 normals). Baltimore ~20 in/yr — conflict: 20.1 (ChaseDay), 21.1 (StudyCountry), 18.5 (BestPlaces-style table), all printed. Oakland “127 in” (StudyCountry) flagged as unverified.
- Snow load and wind: ASCE 7 ground snow load 15–30 psf statewide (secondary guide); Montgomery County minimum ground snow load 30 psf (county amendment); design wind baseline 115 mph 3-second gust, rising toward the coast (IRC wind map, per SRC); Montgomery County Risk Category II V=115 mph. No Garrett County snow-load figure and no coastal design wind figure verified — none stated.
- Code and permits: Baltimore City Building Code adopts the 2021 IBC/IRC with MBPS modifications; IRC R905.1.2 ice barrier (24 in inside the wall line, where the local Table R301.2 requires it); IRC R908.3.1.1 two-layer limit; Baltimore City Work Exempt From Permit list — replacing roof shingles and roof tarring on one- and two-family homes (NumeralQ; Cox Roofing, Nov 12, 2026, with the membrane caveat); Baltimore County 50% sheathing rule + historic/floodplain/Critical Area permits; Carroll County no re-roof permit, code compliance still required; Prince George’s County permits + inspections; Talbot County full-replacement permits via OpenGov (Bay Area Exteriors, Nov 2026).
- Licensing: no roofer-only license in Maryland; MHIC license required for roofing on existing homes (Business Regulation §8-301; RoofingLicenseCheck, checked Oct 22, 2026); 2+ years experience, PSI exam 70% pass mark before applying, financial solvency, $500,000 general liability effective June 1, 2024 (§8-302.1, up from $50,000); no classes, specialties, or reciprocity; first license $403.75 + PSI exam fee ($63 secondary, unverified on the MHIC fees page); deposit cap one-third of contract price (§8-617(b)); Guaranty Fund up to $30,000 per claimant or amount paid, whichever is less, up to $250,000 per contractor (§8-405, per NumeralQ and LegalClarity) vs $20,000/$100,000 in older sources — conflict flagged; unlicensed work a misdemeanor (§8-601): first conviction up to $1,000/30 days, second up to $5,000/two years; mechanic’s liens — sub-lien notice within 120 days, limited to amount owed (Real Prop. §9-104), lien releases at final payment (§9-114).
- Labor (BLS OEWS May 2025): Maryland roofer median $28.89/hr, mean $29.63, 2,050 employed, 10th $22.00, 90th $38.69; national median $26.65. Metro medians: Baltimore-Columbia-Towson $27.11, Salisbury $22.75, Balance of State $22.95, Philadelphia-Camden-Wilmington $28.72. Conflict: SmartRoofingCalculator’s May 2024 vintage lists the Maryland median at $25.00/hr — this guide uses May 2025.
- Insurance: NerdWallet (May 6, 2026) Maryland $2,375/yr at $400,000 dwelling (national $2,490); MoneyGeek (Jun 19, 2026) $2,633/yr, rank 31 of 51, −26% vs national $3,548; updated MoneyGeek pages $2,623/yr; InsuranceQuotes (rates Sep 30, 2026) $3,146/yr at $300,000 dwelling with 2% hurricane deductible; NAIC 2023 average HO-3 premium $1,578/yr; Maryland prohibits credit-score use in home insurance pricing; homes built 2020 $1,669/yr vs 1980 $2,870/yr (MoneyGeek). Hurricane deductibles: III background + Insurance §19-209 / Ch. 491 (2016) — statewide application on any-part warning, 24-hour tail, 5% Coverage A cap unless MIA-filed, mandatory mitigation-discount offer for inspected qualified improvements; percentage deductibles typically 1–5% (III); raising the deductible from $500 to $1,000 typically cuts the premium 10–25% (III, national).
- Class 4 + insurance discounts: UL 2218 Class 4 test (2-inch steel ball from 20 feet); upgrade cost: Lifelong Insurance Agency, Michigan (May 4, 2026: ~$30 more per square — applied here as modeled arithmetic, no Maryland-specific premium verified); national guides (10–25% premium, $1,000–$2,500 on a typical house); discount ranges 5–20% / 10–25% / 15–20% / 20–30% off the wind/hail portion by source, conflict flagged; products named — GAF Timberline AS II, CertainTeed Landmark IR, Owens Corning Duration STORM.
- Salt air and metal: aluminum preferred within 1–2 miles of tidal water; coastal-grade adder $1,200–$3,500 (G.H. Clark); steel warranty limits near salt water (SB Roofing, adjacent-market guidance, flagged); compatible-metal fasteners and flashings (NRCIA, Nov 11, 2026); exposed-fastener screw leaks 7–10 years near salt water (single coastal inspector, RenovateGuide, Oct 25, 2026 — flagged).
- Federal help: OBBBA (P.L. 119-21; IRS FS-2025-05) ended §25C/§25D for post-Dec-31-2025 installs — $0 federal credit for a 2026 owned install. HEAR/HOMES NOT launched in Maryland (MEA resubmitted applications Sep 30, 2026; no launch date, verified Nov 4–9, 2026, per art 140 brief): HEAR up to $8,000, electric-to-electric only per DOE Program Notice 26-2 dated May 29, 2026; HOMES up to $4,000 general, up to $8,000 low-income; HEAR never pays for a roof. No Maryland state roof grant, rebate or tax credit verified; no utility roof rebate verified. Detach-and-reset for a later reroof $1,500–$5,000 (EcoGen, per art 140 brief).
- Lifespans: the Maryland lifespans here are contractor-consensus estimates, fitted to a climate of Bay wind, salt air, humid summers, hail, and a split winter. The lifespans are realistic figures, not numbers lifted from a single published table.
Prices change, and a quote from last month is not a quote from today. Verify every figure against a current written bid before signing.
EXCLUDED: Columbia, Germantown, and Annapolis city-only NumeralQ/SRC figures (none verified — Modernize metro bands used instead); a Maryland-specific Class 4 premium and any carrier-specific Maryland Class 4 discount (modeled/national ranges used, labeled as such); a Maryland-specific roof-age underwriting trigger (industry pattern used, labeled as such); a Garrett-County-specific adopted snow load and a coastal-specific design wind speed (none verified); a Maryland-specific attic insulation R-value code requirement (none verified); the Oakland “127 inches” snowfall figure (weak source); the 2022 “no permit anywhere in Maryland” claim (outdated/overbroad); any Maryland state or utility roof grant, rebate, or tax credit (none verified); DHCD repair-program roof eligibility (not verified); the MHIC $500 threshold reading and the $20,000 Guaranty Fund cap (older/conflicting sources — conflicts flagged in the text).
*Disclaimer: This guide is general information, not professional advice. Prices are 2026 estimates for Maryland based on the sources cited and will vary with roof size, pitch, condition, material, and contractor. Permits, codes, and licensing rules vary by city and county — confirm them with the local building department. Insurance terms, deductibles, and discounts vary by carrier and policy — confirm them with your own insurer before signing. Always obtain multiple written quotes from licensed local contractors before making a decision.*
What does a roof replacement cost in Maryland in 2026?
A typical 25-square architectural shingle roof costs $11,750–$16,750 in 2026, per SmartRoofingCalculator, and a 2,000 square foot roof costs $10,110–$12,360 statewide, per NumeralQ (pricing October 26, 2026). On that 25-square roof, 3-tab shingles run $9,625–$15,125 before tear-off. Class 4 impact-rated shingles run $12,500–$17,500 as modeled arithmetic, and standing-seam metal runs $23,250–$36,250. Baltimore runs $9,790–$11,950 for a 2,000 square foot roof, Rockville $9,960–$12,160, and the Annapolis metro $13,500–$23,000 on Modernize’s bands.
How much does a roof cost per square in Maryland?
Architectural shingles run $470–$670 per square fitted with tear-off, per SmartRoofingCalculator. MyRoofData prices the same material at $495–$825 a square before tear-off. Class 4 impact-rated shingles run $500–$700 a square as modeled arithmetic — a Michigan agent’s $30-a-square premium applied to the Maryland architectural band, because no Maryland-specific Class 4 premium was verified. Standing-seam metal runs $930–$1,450 a square fitted, and 3-tab $385–$605 before tear-off. A square covers 100 square feet of finished roof surface, and every Maryland bid is written in squares.
Do I need a permit to replace a roof in Maryland?
It depends on the county, and in one city it depends on the scope. Baltimore City exempts replacing roof shingles and roof tarring on one- and two-family homes, but membrane replacements, deck work, and structural changes can still need a permit. Carroll County needs no permit for re-roofing, though the work must meet code. Baltimore County needs one when half or more of the sheathing is replaced, and always in historic districts, floodplains, and the Chesapeake Bay Critical Area. Prince George’s County and Talbot County require permits for full replacements. Fees run about $200–$500 per SmartRoofingCalculator, $100–$400 per MyRoofData, and $250–$800 per RoofingEstimatorPros. When the county and the contractor disagree, the building department’s answer is the one that governs.
Does Maryland license roofers?
Maryland has no roofer-only license. Roofing on an existing home is home improvement, so the contractor needs a Maryland Home Improvement Commission (MHIC) license: two or more years of experience, a PSI exam passed at 70 percent before applying, proof of financial solvency, and at least $500,000 in general liability insurance since June 1, 2024. The license has no classes, no specialties, and no reciprocity with other states. Unlicensed home improvement work is a misdemeanor, and hiring an unlicensed contractor closes off the Home Improvement Guaranty Fund entirely. Verify the number on the Maryland Department of Labor’s license lookup before signing.
How much does a flat roof cost on a Baltimore rowhome?
A typical Baltimore rowhouse roof of 1,200 to 1,800 square feet runs $6,000–$13,000, per Monarch Bay Renovations. On a 14-square, 1,400-square-foot roof, EPDM runs $7,700–$11,900, TPO $9,800–$15,400, and modified bitumen $9,100–$14,000. Per-square-foot figures vary by source and scope: EPDM $5.50–$15, TPO $6.66–$18, and modified bitumen $5–$10 across the sources this guide checked. Lifespans run 20–30 years for EPDM, 15–25 for TPO, and 15–20 for modified bitumen. Parapet flashing, drainage, decking, and access are separate lines on an honest rowhome quote.
How does the Maryland hurricane deductible work on a roof claim?
Maryland law lets a mandatory percentage hurricane deductible apply statewide once the National Hurricane Center issues a hurricane warning for any part of the state, until 24 hours after the last warning ends, regardless of where the home sits. A warning for Ocean City can trigger the percentage deductible on a house in Oakland. Mandatory deductibles may not exceed 5 percent of the Coverage A dwelling limit unless the insurer has filed an underwriting standard with the Maryland Insurance Administration. At 2 percent on a $300,000 dwelling, the homeowner pays $6,000 before the insurer pays anything on a wind claim. The same law requires insurers to offer a premium discount for qualified wind-mitigation improvements inspected by a licensed contractor.
How long does a roof last in Maryland?
Bay wind, salt air, humid summers, and the western winter cut shingle life short and leave metal and slate standing longer than the brochure claims. Natural slate lasts 75–150 years and tile 50 years or more; standing-seam metal 40–60 and ribbed metal 30–40; cedar shakes 20–30; Class 4 shingles 25–30, architectural shingles 20–25, and 3-tab 15–20. Flat membranes run 20–30 years for EPDM, 15–25 for TPO, and 15–20 for modified bitumen. Those lives get cut short by hail, wind-driven debris, salt corrosion on the wrong metal, and ice dams in the west. Check the roof twice a year: in fall, once the hail season has wound down, and in spring, before it starts up.
Can I get a rebate or tax credit for a new roof in Maryland in 2026?
No. A roof finished after December 31, 2025 draws nothing from either federal credit. Neither the 30-percent Residential Clean Energy Credit (§25D) nor the Energy Efficient Home Improvement Credit (§25C) pays anything on it. The cutoff comes from the One Big Beautiful Bill Act, signed July 4, 2025 — Public Law 119-21 closed both credits for installs finished after 2025. Maryland’s HEAR and HOMES rebates have not launched — the Maryland Energy Administration resubmitted the state’s applications on September 30, 2026, with no launch date set — and HEAR never pays for a roof in any case. This pass turned up no Maryland state roof grant, rebate, or tax credit, and no utility roof rebate either. The insurer is the one that pays: a Class 4 roof can earn a discount on the wind and hail portion of the premium, a high-wind specification can earn the mitigation discount, and each claim avoided is a deductible the homeowner keeps.
